mirror/linux
1
0
Fork 0
mirror of https://github.com/torvalds/linux.git synced 2024-11-21 19:46:16 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
master
linux/drivers/gpio/gpio-pcie-idio-24.c

402 lines
13 KiB
C
Raw Permalink Normal View History

gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
// SPDX-License-Identifier: GPL-2.0-only
/*
* GPIO driver for the ACCES PCIe-IDIO-24 family
* Copyright (C) 2018 William Breathitt Gray
*
* This driver supports the following ACCES devices: PCIe-IDIO-24,
* PCIe-IDI-24, PCIe-IDO-24, and PCIe-IDIO-12.
*/
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
#include <linux/bits.h>
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
#include <linux/device.h>
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
#include <linux/err.h>
#include <linux/gpio/regmap.h>
#include <linux/irq.h>
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
#include <linux/regmap.h>
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
#include <linux/spinlock.h>
#include <linux/types.h>
gpio: pcie-idio-24: Enable PEX8311 interrupts This enables the PEX8311 internal PCI wire interrupt and the PEX8311 local interrupt input so the local interrupts are forwarded to the PCI. Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family") Cc: stable@vger.kernel.org Signed-off-by: Arnaud de Turckheim <quarium@gmail.com> Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-11-04 15:24:55 +00:00
/*
* PLX PEX8311 PCI LCS_INTCSR Interrupt Control/Status
*
* Bit: Description
* 0: Enable Interrupt Sources (Bit 0)
* 1: Enable Interrupt Sources (Bit 1)
* 2: Generate Internal PCI Bus Internal SERR# Interrupt
* 3: Mailbox Interrupt Enable
* 4: Power Management Interrupt Enable
* 5: Power Management Interrupt
* 6: Slave Read Local Data Parity Check Error Enable
* 7: Slave Read Local Data Parity Check Error Status
* 8: Internal PCI Wire Interrupt Enable
* 9: PCI Express Doorbell Interrupt Enable
* 10: PCI Abort Interrupt Enable
* 11: Local Interrupt Input Enable
* 12: Retry Abort Enable
* 13: PCI Express Doorbell Interrupt Active
* 14: PCI Abort Interrupt Active
* 15: Local Interrupt Input Active
* 16: Local Interrupt Output Enable
* 17: Local Doorbell Interrupt Enable
* 18: DMA Channel 0 Interrupt Enable
* 19: DMA Channel 1 Interrupt Enable
* 20: Local Doorbell Interrupt Active
* 21: DMA Channel 0 Interrupt Active
* 22: DMA Channel 1 Interrupt Active
* 23: Built-In Self-Test (BIST) Interrupt Active
* 24: Direct Master was the Bus Master during a Master or Target Abort
* 25: DMA Channel 0 was the Bus Master during a Master or Target Abort
* 26: DMA Channel 1 was the Bus Master during a Master or Target Abort
* 27: Target Abort after internal 256 consecutive Master Retrys
* 28: PCI Bus wrote data to LCS_MBOX0
* 29: PCI Bus wrote data to LCS_MBOX1
* 30: PCI Bus wrote data to LCS_MBOX2
* 31: PCI Bus wrote data to LCS_MBOX3
*/
#define PLX_PEX8311_PCI_LCS_INTCSR 0x68
#define INTCSR_INTERNAL_PCI_WIRE BIT(8)
#define INTCSR_LOCAL_INPUT BIT(11)
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
#define IDIO_24_ENABLE_IRQ (INTCSR_INTERNAL_PCI_WIRE | INTCSR_LOCAL_INPUT)
#define IDIO_24_OUT_BASE 0x0
#define IDIO_24_TTLCMOS_OUT_REG 0x3
#define IDIO_24_IN_BASE 0x4
#define IDIO_24_TTLCMOS_IN_REG 0x7
#define IDIO_24_COS_STATUS_BASE 0x8
#define IDIO_24_CONTROL_REG 0xC
#define IDIO_24_COS_ENABLE 0xE
#define IDIO_24_SOFT_RESET 0xF
#define CONTROL_REG_OUT_MODE BIT(1)
#define COS_ENABLE_RISING BIT(1)
#define COS_ENABLE_FALLING BIT(4)
#define COS_ENABLE_BOTH (COS_ENABLE_RISING | COS_ENABLE_FALLING)
static const struct regmap_config pex8311_intcsr_regmap_config = {
.name = "pex8311_intcsr",
.reg_bits = 32,
.reg_stride = 1,
.reg_base = PLX_PEX8311_PCI_LCS_INTCSR,
.val_bits = 32,
.io_port = true,
};
gpio: pcie-idio-24: Enable PEX8311 interrupts This enables the PEX8311 internal PCI wire interrupt and the PEX8311 local interrupt input so the local interrupts are forwarded to the PCI. Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family") Cc: stable@vger.kernel.org Signed-off-by: Arnaud de Turckheim <quarium@gmail.com> Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-11-04 15:24:55 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
static const struct regmap_range idio_24_wr_ranges[] = {
regmap_reg_range(0x0, 0x3), regmap_reg_range(0x8, 0xC),
regmap_reg_range(0xE, 0xF),
};
static const struct regmap_range idio_24_rd_ranges[] = {
regmap_reg_range(0x0, 0xC), regmap_reg_range(0xE, 0xF),
};
static const struct regmap_range idio_24_volatile_ranges[] = {
regmap_reg_range(0x4, 0xB), regmap_reg_range(0xF, 0xF),
};
static const struct regmap_access_table idio_24_wr_table = {
.yes_ranges = idio_24_wr_ranges,
.n_yes_ranges = ARRAY_SIZE(idio_24_wr_ranges),
};
static const struct regmap_access_table idio_24_rd_table = {
.yes_ranges = idio_24_rd_ranges,
.n_yes_ranges = ARRAY_SIZE(idio_24_rd_ranges),
};
static const struct regmap_access_table idio_24_volatile_table = {
.yes_ranges = idio_24_volatile_ranges,
.n_yes_ranges = ARRAY_SIZE(idio_24_volatile_ranges),
};
static const struct regmap_config idio_24_regmap_config = {
.reg_bits = 8,
.reg_stride = 1,
.val_bits = 8,
.io_port = true,
.wr_table = &idio_24_wr_table,
.rd_table = &idio_24_rd_table,
.volatile_table = &idio_24_volatile_table,
.cache_type = REGCACHE_FLAT,
.use_raw_spinlock = true,
};
#define IDIO_24_NGPIO_PER_REG 8
#define IDIO_24_REGMAP_IRQ(_id) \
[24 + _id] = { \
.reg_offset = (_id) / IDIO_24_NGPIO_PER_REG, \
.mask = BIT((_id) % IDIO_24_NGPIO_PER_REG), \
.type = { .types_supported = IRQ_TYPE_EDGE_BOTH }, \
}
#define IDIO_24_IIN_IRQ(_id) IDIO_24_REGMAP_IRQ(_id)
#define IDIO_24_TTL_IRQ(_id) IDIO_24_REGMAP_IRQ(24 + _id)
static const struct regmap_irq idio_24_regmap_irqs[] = {
IDIO_24_IIN_IRQ(0), IDIO_24_IIN_IRQ(1), IDIO_24_IIN_IRQ(2), /* IIN 0-2 */
IDIO_24_IIN_IRQ(3), IDIO_24_IIN_IRQ(4), IDIO_24_IIN_IRQ(5), /* IIN 3-5 */
IDIO_24_IIN_IRQ(6), IDIO_24_IIN_IRQ(7), IDIO_24_IIN_IRQ(8), /* IIN 6-8 */
IDIO_24_IIN_IRQ(9), IDIO_24_IIN_IRQ(10), IDIO_24_IIN_IRQ(11), /* IIN 9-11 */
IDIO_24_IIN_IRQ(12), IDIO_24_IIN_IRQ(13), IDIO_24_IIN_IRQ(14), /* IIN 12-14 */
IDIO_24_IIN_IRQ(15), IDIO_24_IIN_IRQ(16), IDIO_24_IIN_IRQ(17), /* IIN 15-17 */
IDIO_24_IIN_IRQ(18), IDIO_24_IIN_IRQ(19), IDIO_24_IIN_IRQ(20), /* IIN 18-20 */
IDIO_24_IIN_IRQ(21), IDIO_24_IIN_IRQ(22), IDIO_24_IIN_IRQ(23), /* IIN 21-23 */
IDIO_24_TTL_IRQ(0), IDIO_24_TTL_IRQ(1), IDIO_24_TTL_IRQ(2), /* TTL 0-2 */
IDIO_24_TTL_IRQ(3), IDIO_24_TTL_IRQ(4), IDIO_24_TTL_IRQ(5), /* TTL 3-5 */
IDIO_24_TTL_IRQ(6), IDIO_24_TTL_IRQ(7), /* TTL 6-7 */
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
};
/**
* struct idio_24_gpio - GPIO device private data structure
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
* @map: regmap for the device
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
* @lock: synchronization lock to prevent I/O race conditions
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
* @irq_type: type configuration for IRQs
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
*/
struct idio_24_gpio {
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
struct regmap *map;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
raw_spinlock_t lock;
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
u8 irq_type;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
};
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
static int idio_24_handle_mask_sync(const int index, const unsigned int mask_buf_def,
const unsigned int mask_buf, void *const irq_drv_data)
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
{
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
const unsigned int type_mask = COS_ENABLE_BOTH << index;
struct idio_24_gpio *const idio24gpio = irq_drv_data;
u8 type;
int ret;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
raw_spin_lock(&idio24gpio->lock);
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* if all are masked, then disable interrupts, else set to type */
type = (mask_buf == mask_buf_def) ? ~type_mask : idio24gpio->irq_type;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
ret = regmap_update_bits(idio24gpio->map, IDIO_24_COS_ENABLE, type_mask, type);
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
raw_spin_unlock(&idio24gpio->lock);
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks The ACCES I/O PCIe-IDIO-24 series of devices provides 24 optically-isolated digital I/O accessed via six 8-bit ports. Since eight input lines are acquired on a single port input read -- and similarly eight output lines are set on a single port output write -- the PCIe-IDIO-24 GPIO driver may improve multiple I/O reads/writes by utilizing a get_multiple/set_multiple callbacks. This patch implements the idio_24_gpio_get_multiple function which serves as the respective get_multiple callback, and implements the idio_24_gpio_set_multiple function which serves as the respective set_multiple callback. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-22 13:00:00 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
return ret;
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks The ACCES I/O PCIe-IDIO-24 series of devices provides 24 optically-isolated digital I/O accessed via six 8-bit ports. Since eight input lines are acquired on a single port input read -- and similarly eight output lines are set on a single port output write -- the PCIe-IDIO-24 GPIO driver may improve multiple I/O reads/writes by utilizing a get_multiple/set_multiple callbacks. This patch implements the idio_24_gpio_get_multiple function which serves as the respective get_multiple callback, and implements the idio_24_gpio_set_multiple function which serves as the respective set_multiple callback. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-22 13:00:00 +00:00
}
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
static int idio_24_set_type_config(unsigned int **const buf, const unsigned int type,
const struct regmap_irq *const irq_data, const int idx,
void *const irq_drv_data)
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
{
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
const unsigned int offset = irq_data->reg_offset;
const unsigned int rising = COS_ENABLE_RISING << offset;
const unsigned int falling = COS_ENABLE_FALLING << offset;
const unsigned int mask = COS_ENABLE_BOTH << offset;
struct idio_24_gpio *const idio24gpio = irq_drv_data;
unsigned int new;
unsigned int cos_enable;
int ret;
switch (type) {
case IRQ_TYPE_EDGE_RISING:
new = rising;
break;
case IRQ_TYPE_EDGE_FALLING:
new = falling;
break;
case IRQ_TYPE_EDGE_BOTH:
new = mask;
break;
default:
return -EINVAL;
gpio: pcie-idio-24: utilize for_each_set_clump8 macro Replace verbose implementation in get_multiple/set_multiple callbacks with for_each_set_clump8 macro to simplify code and improve clarity. Link: http://lkml.kernel.org/r/d5d22fa9809dcf8330f4381dbe7e7ca37990e79f.1570641097.git.vilhelm.gray@gmail.com Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Lukas Wunner <lukas@wunner.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Mathias Duckeck <m.duckeck@kunbus.de> Cc: Morten Hein Tiljeset <morten.tiljeset@prevas.dk> Cc: Phil Reid <preid@electromag.com.au> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-12-05 00:51:22 +00:00
}
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
raw_spin_lock(&idio24gpio->lock);
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* replace old bitmap with new bitmap */
idio24gpio->irq_type = (idio24gpio->irq_type & ~mask) | (new & mask);
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
ret = regmap_read(idio24gpio->map, IDIO_24_COS_ENABLE, &cos_enable);
if (ret)
goto exit_unlock;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* if COS is currently enabled then update the edge type */
if (cos_enable & mask) {
ret = regmap_update_bits(idio24gpio->map, IDIO_24_COS_ENABLE, mask,
idio24gpio->irq_type);
if (ret)
goto exit_unlock;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
}
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
exit_unlock:
raw_spin_unlock(&idio24gpio->lock);
gpio: pcie-idio-24: Convert to immutable irq_chip Convert the driver to immutable irq-chip with a bit of intuition. Cc: Marc Zyngier <maz@kernel.org> Acked-by: William Breathitt Gray <william.gray@linaro.org> Acked-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-03-09 07:46:05 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
return ret;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
}
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
static int idio_24_reg_mask_xlate(struct gpio_regmap *const gpio, const unsigned int base,
const unsigned int offset, unsigned int *const reg,
unsigned int *const mask)
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
{
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
const unsigned int out_stride = offset / IDIO_24_NGPIO_PER_REG;
const unsigned int in_stride = (offset - 24) / IDIO_24_NGPIO_PER_REG;
struct regmap *const map = gpio_regmap_get_drvdata(gpio);
int err;
unsigned int ctrl_reg;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
switch (base) {
case IDIO_24_OUT_BASE:
*mask = BIT(offset % IDIO_24_NGPIO_PER_REG);
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* FET Outputs */
if (offset < 24) {
*reg = IDIO_24_OUT_BASE + out_stride;
return 0;
}
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* Isolated Inputs */
if (offset < 48) {
*reg = IDIO_24_IN_BASE + in_stride;
return 0;
}
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
err = regmap_read(map, IDIO_24_CONTROL_REG, &ctrl_reg);
if (err)
return err;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* TTL/CMOS Outputs */
if (ctrl_reg & CONTROL_REG_OUT_MODE) {
*reg = IDIO_24_TTLCMOS_OUT_REG;
return 0;
}
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* TTL/CMOS Inputs */
*reg = IDIO_24_TTLCMOS_IN_REG;
return 0;
case IDIO_24_CONTROL_REG:
/* We can only set direction for TTL/CMOS lines */
if (offset < 48)
gpio: pcie-idio-24: Use -ENOTSUPP consistently The GPIO library expects the drivers to return -ENOTSUPP in some cases and not using analogue POSIX code. Make the driver to follow this. Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: William Breathitt Gray <wbg@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2024-04-10 06:41:56 +00:00
return -ENOTSUPP;
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
*reg = IDIO_24_CONTROL_REG;
*mask = CONTROL_REG_OUT_MODE;
return 0;
default:
/* Should never reach this path */
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
return -EINVAL;
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
}
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
}
#define IDIO_24_NGPIO 56
static const char *idio_24_names[IDIO_24_NGPIO] = {
"OUT0", "OUT1", "OUT2", "OUT3", "OUT4", "OUT5", "OUT6", "OUT7",
"OUT8", "OUT9", "OUT10", "OUT11", "OUT12", "OUT13", "OUT14", "OUT15",
"OUT16", "OUT17", "OUT18", "OUT19", "OUT20", "OUT21", "OUT22", "OUT23",
"IIN0", "IIN1", "IIN2", "IIN3", "IIN4", "IIN5", "IIN6", "IIN7",
"IIN8", "IIN9", "IIN10", "IIN11", "IIN12", "IIN13", "IIN14", "IIN15",
"IIN16", "IIN17", "IIN18", "IIN19", "IIN20", "IIN21", "IIN22", "IIN23",
"TTL0", "TTL1", "TTL2", "TTL3", "TTL4", "TTL5", "TTL6", "TTL7"
};
static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
{
struct device *const dev = &pdev->dev;
struct idio_24_gpio *idio24gpio;
int err;
gpio: pcie-idio-24: Enable PEX8311 interrupts This enables the PEX8311 internal PCI wire interrupt and the PEX8311 local interrupt input so the local interrupts are forwarded to the PCI. Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family") Cc: stable@vger.kernel.org Signed-off-by: Arnaud de Turckheim <quarium@gmail.com> Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-11-04 15:24:55 +00:00
const size_t pci_plx_bar_index = 1;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
const size_t pci_bar_index = 2;
const char *const name = pci_name(pdev);
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
struct gpio_regmap_config gpio_config = {};
void __iomem *pex8311_regs;
void __iomem *idio_24_regs;
struct regmap *intcsr_map;
struct regmap_irq_chip *chip;
struct regmap_irq_chip_data *chip_data;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
err = pcim_enable_device(pdev);
gpio: pcie-idio-24: Replace deprecated PCI functions pcim_iomap_regions() and pcim_iomap_table() have been deprecated in commit e354bb84a4c1 ("PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()"). Replace these functions with pcim_iomap_region(). In order to match the rest of the code in idio_24_probe(), utilize dev_err_probe() to handle error for pcim_enable_device(). Signed-off-by: William Breathitt Gray <wbg@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20241101-pci_iomap_region_gpio_acces-v1-2-26eb1dc93e45@kernel.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2024-11-01 07:15:09 +00:00
if (err)
return dev_err_probe(dev, err, "Failed to enable PCI device\n");
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Replace deprecated PCI functions pcim_iomap_regions() and pcim_iomap_table() have been deprecated in commit e354bb84a4c1 ("PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()"). Replace these functions with pcim_iomap_region(). In order to match the rest of the code in idio_24_probe(), utilize dev_err_probe() to handle error for pcim_enable_device(). Signed-off-by: William Breathitt Gray <wbg@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20241101-pci_iomap_region_gpio_acces-v1-2-26eb1dc93e45@kernel.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2024-11-01 07:15:09 +00:00
pex8311_regs = pcim_iomap_region(pdev, pci_plx_bar_index, "pex8311");
if (IS_ERR(pex8311_regs))
return dev_err_probe(dev, PTR_ERR(pex8311_regs), "Unable to map PEX 8311 I/O addresses\n");
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
gpio: pcie-idio-24: Replace deprecated PCI functions pcim_iomap_regions() and pcim_iomap_table() have been deprecated in commit e354bb84a4c1 ("PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()"). Replace these functions with pcim_iomap_region(). In order to match the rest of the code in idio_24_probe(), utilize dev_err_probe() to handle error for pcim_enable_device(). Signed-off-by: William Breathitt Gray <wbg@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20241101-pci_iomap_region_gpio_acces-v1-2-26eb1dc93e45@kernel.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2024-11-01 07:15:09 +00:00
idio_24_regs = pcim_iomap_region(pdev, pci_bar_index, name);
if (IS_ERR(idio_24_regs))
return dev_err_probe(dev, PTR_ERR(idio_24_regs), "Unable to map PCIe-IDIO-24 I/O addresses\n");
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
intcsr_map = devm_regmap_init_mmio(dev, pex8311_regs, &pex8311_intcsr_regmap_config);
if (IS_ERR(intcsr_map))
return dev_err_probe(dev, PTR_ERR(intcsr_map),
"Unable to initialize PEX8311 register map\n");
idio24gpio = devm_kzalloc(dev, sizeof(*idio24gpio), GFP_KERNEL);
if (!idio24gpio)
return -ENOMEM;
idio24gpio->map = devm_regmap_init_mmio(dev, idio_24_regs, &idio_24_regmap_config);
if (IS_ERR(idio24gpio->map))
return dev_err_probe(dev, PTR_ERR(idio24gpio->map),
"Unable to initialize register map\n");
gpio: pcie-idio-24: Use irqchip template This makes the driver use the irqchip template to assign properties to the gpio_irq_chip instead of using the explicit call to gpiochip_irqchip_add(). The irqchip is instead added while adding the gpiochip. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Cc: William Breathitt Gray <vilhelm.gray@gmail.com> Link: https://lore.kernel.org/r/20200722110027.192782-1-linus.walleij@linaro.org
2020-07-22 11:00:27 +00:00
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
raw_spin_lock_init(&idio24gpio->lock);
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
/* Initialize all IRQ type configuration to IRQ_TYPE_EDGE_BOTH */
idio24gpio->irq_type = GENMASK(7, 0);
chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
chip->name = name;
chip->status_base = IDIO_24_COS_STATUS_BASE;
chip->mask_base = IDIO_24_COS_ENABLE;
chip->ack_base = IDIO_24_COS_STATUS_BASE;
chip->num_regs = 4;
chip->irqs = idio_24_regmap_irqs;
chip->num_irqs = ARRAY_SIZE(idio_24_regmap_irqs);
chip->handle_mask_sync = idio_24_handle_mask_sync;
chip->set_type_config = idio_24_set_type_config;
chip->irq_drv_data = idio24gpio;
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
/* Software board reset */
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
err = regmap_write(idio24gpio->map, IDIO_24_SOFT_RESET, 0);
if (err)
return err;
gpio: pcie-idio-24: Enable PEX8311 interrupts This enables the PEX8311 internal PCI wire interrupt and the PEX8311 local interrupt input so the local interrupts are forwarded to the PCI. Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family") Cc: stable@vger.kernel.org Signed-off-by: Arnaud de Turckheim <quarium@gmail.com> Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-11-04 15:24:55 +00:00
/*
* enable PLX PEX8311 internal PCI wire interrupt and local interrupt
* input
*/
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
err = regmap_update_bits(intcsr_map, 0x0, IDIO_24_ENABLE_IRQ, IDIO_24_ENABLE_IRQ);
if (err)
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
return err;
gpio: pcie-idio-24: Migrate to the regmap API The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-08-10 22:00:42 +00:00
err = devm_regmap_add_irq_chip(dev, idio24gpio->map, pdev->irq, 0, 0, chip, &chip_data);
if (err)
return dev_err_probe(dev, err, "IRQ registration failed\n");
gpio_config.parent = dev;
gpio_config.regmap = idio24gpio->map;
gpio_config.ngpio = IDIO_24_NGPIO;
gpio_config.names = idio_24_names;
gpio_config.reg_dat_base = GPIO_REGMAP_ADDR(IDIO_24_OUT_BASE);
gpio_config.reg_set_base = GPIO_REGMAP_ADDR(IDIO_24_OUT_BASE);
gpio_config.reg_dir_out_base = GPIO_REGMAP_ADDR(IDIO_24_CONTROL_REG);
gpio_config.ngpio_per_reg = IDIO_24_NGPIO_PER_REG;
gpio_config.irq_domain = regmap_irq_get_domain(chip_data);
gpio_config.reg_mask_xlate = idio_24_reg_mask_xlate;
gpio_config.drvdata = idio24gpio->map;
return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(dev, &gpio_config));
gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines of optically-isolated non-polarized digital inputs for AC and DC control signals, 24 lines of isolated solid state FET digital outputs, and 8 non-isolated TTL/CMOS compatible programmable I/O). An interrupt is generated when any of the inputs change state (low to high or high to low). Input filter control is not supported by this driver, and input filters are deactivated by this driver. These devices are capable of get_multiple and set_multiple functionality, but these functions have not yet been implemented for this driver. Change-Of-State (COS) detection functionality may be configured to fire interrupts on exclusively rising/falling edges, but this driver currently only implements COS detection for either both edges or none. Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 22:21:45 +00:00
}
static const struct pci_device_id idio_24_pci_dev_id[] = {
{ PCI_DEVICE(0x494F, 0x0FD0) }, { PCI_DEVICE(0x494F, 0x0BD0) },
{ PCI_DEVICE(0x494F, 0x07D0) }, { PCI_DEVICE(0x494F, 0x0FC0) },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, idio_24_pci_dev_id);
static struct pci_driver idio_24_driver = {
.name = "pcie-idio-24",
.id_table = idio_24_pci_dev_id,
.probe = idio_24_probe
};
module_pci_driver(idio_24_driver);
MODULE_AUTHOR("William Breathitt Gray <vilhelm.gray@gmail.com>");
MODULE_DESCRIPTION("ACCES PCIe-IDIO-24 GPIO driver");
MODULE_LICENSE("GPL v2");
Reference in New Issue Copy Permalink